跳至主要内容

Defoamer for industrial circulating water


Defoamer for industrial circulating water

Industrial circulating water defoamer is a defoamer developed according to the characteristics of industrial circulating water foaming in the cooling water system. Industrial circulating water is also called cooling circulating water, and is mainly composed of a circulating pump, a control system, a check valve, and the like. However, when water treatment is carried out using industrial cycle machine technology, foam is easily generated due to agitation, entry of soluble gas, equipment, water quality, additives, and the like. If these foams are discharged without treatment, the impact on the ecological environment will be very large. Therefore, it is necessary to use industrial circulating water defoamer at this time.
Industrial circulating water process    


The industrial circulating water defoaming agent is a defoaming agent which is prepared by compounding a modified silicon polyether with a modified siloxane and using a special process. It can solve the foam problem that occurs when industrial circulating water technology is used. It has alkali and acid resistance, fast defoaming speed, long foam suppression time and high efficiency. Low COD and low consumption.

Hazards of foam in industrial circulating water:

1. The bubble will cause the EPA to fail to meet the standards, fail to discharge, and slow down the progress of the work.
2. Too much foam overflows from the surface, causing serious pollution of the external environment.
3, the bubble will affect the appearance, the appearance is difficult to see
4. When there is aeration or oxygen supply during biological water treatment, there is too much foam, which affects the progress or overflow of water treatment, affecting the active mud and bacteria.
5. Excessive circulation of water foam affects secondary utilization, affecting production progress, and more seriously affecting the production of products.











Industrial circulating water defoamer application site

Reasons for foaming in industrial circulating water:

1. The wastewater treated by the water treatment equipment contains a certain amount of foam. If the temperature of the influent water is high, the foam particles will be large, and more will be produced.
2. Other impurities, gases, etc. in the water are mixed with the organic matter mixed with water to generate a large number of bubbles under the mechanical stirring of the water stream.
3, due to the high content of organic matter in the water, resulting in foaming
4, due to the addition of other additives to produce a chemical reaction, resulting in foaming
5, due to too much suspended matter, causing foaming
6, because there is no good management of water quality, resulting in foaming
https://www.ywlchemical.com/industries/waste-water/
https://www.ywlchemical.com/products/foam-control-agent/

标签：

评论

发表评论

此博客中的热门博文

How do we assess antifoam efficiency ?

How do we assess antifoam efficiency ? Quality of an antifoam is given by two main characteristics : • Knockdown ability or shock effect :Meaning the speed to destroy an existing foam. • Persistence or durability : Meaning the efficiency over time.   These two parameters can be assessed by several tests. The main test is the bubbling method. A graduated column with a glass frit in the bottom is required. Foaming water is poured in the column and air at constant flowrate is introduced through the glass frit in the column. Foam is generated by the air and starts to travel up the column. At a determined level of foam, antifoam is injected. By this method several antifoaming agents can be tested. A graph reporting foam height vs time is very helpful to establish the knockdown ability and the persistence for each product. The selected antifoam is the product with the best compromise between shock effect and durability       Environmental performance   Silicone antifo...
1 条评论
阅读全文

Silicone oil is so widely used! Let’s learn silicone oil production technology

Silicone is so widely used! Let's learn silicone oil production technology Silicone oil is a kind of linear small molecule silicone polymer with Si-O-Si as the main chain and organic groups in the side chain. It is widely used in textile, daily chemical, mechanical processing, chemical, electrical and electronic, medical and health, etc. industry. Silicon oil is usually kept in a liquid state at room temperature. As the molecular weight increases, the viscosity also increases, so viscosity is an important physical property index of silicone oil. 2017 China's silicone oil consumption situation Classification of silicone oil Silicone oil is generally divided into two categories: general silicone oil and modified silicone oil. There is also a class of co-modified silicone oils and derivatives - ternary modified silicone oil Silicone oil properties Silicone oil is generally a colorless, odorless, non-toxic, non-volatile liquid with the following characteristics...
发表评论
阅读全文

Defoamer Test Method

Defoamer testing methods are divided into dynamic defoaming and static defoaming tests. If your foaming environment is different, the recommended test methods are different. There are three main types of foam experiments to characterize the activity of defoamers. Persistence. As we have different experimental conditions in different laboratories and the experiments used in our research to obtain results from existing literature, we will introduce these experiments below. Other methods are sometimes used depending on the particular application. 1． Ross-Miles Foam Tester   Features: Tested for strong foaming environments. This experiment is widely used for characterization        (1) Foaming of surfactant solution        (2) Research and application of foam stability in the presence of defoamer In the foaming system, the defoaming performance test was carried out by circulating bubbling by a Ros...
发表评论
阅读全文